Fill Dirt Delivery in Pasco, WA by the Ton

Fill dirt delivery in Pasco, WA is a practical order for homeowners who need a level grade before a patio, a shed or a new lawn. Pasco sits where the Snake and Columbia rivers meet in Franklin County, part of the Tri-Cities area, and uneven ground is a common reason for an order.

How Much Fill Dirt a Pasco Project Needs

Start with the low area's dimensions in feet and multiply length by width. Then multiply that by the depth converted to feet (inches divided by 12). The result is cubic feet, and dividing cubic feet by 27 gives cubic yards, which you then convert to tons using the ratio below.

Leave room for settling in the total. Fill that is spread and tamped in one pass will drop unevenly, so a second pass and a small surplus keep the finished grade where you planned it.

Each cubic yard works out to about 1.1 tons, since a yard of this material weighs close to 2,200 pounds. The calculator can help you set up the numbers if you prefer a worked example.

Getting a Truck to Your Drop Spot in Pasco

Pick a spot the driver can reach on firm ground, ideally a paved apron or a gravel lane rather than a soft lawn. Measure the side yard or gate width before ordering, and look up for low branches along the approach.

Pasco is about 5 miles from Kennewick and about 8 miles from Richland. Local details are on the delivery in Pasco page.

Where Pasco Yards Put Fill Dirt to Work

A backyard that stays soggy after watering is a frequent reason for a fill order here, since irrigated lawns can leave low pockets that stay wet. Fill brings those pockets up to the surrounding grade so water moves across the surface instead of sitting.

Summer heat is the timing factor. Hot, dry ground is easier to shape in the cooler morning hours, and working in full afternoon sun makes the surface hard to handle.

Finish each section with a slight pitch so water runs away from the house and toward the drain or lawn edge. A level spot with no fall will still hold water after a hard rain.

Patio and shed pads

A pad for a patio or shed starts with the height you want at the door threshold or the top of the slab, then works outward. Fill the middle first, since edges are easier to finish once the center is right. A string line stretched across the pad shows where the high and low points sit.

Utility trenches

Trenches for irrigation lines and power conduit get backfilled in stages, with the pipe bedded in sand or fine material first. Keep stones out of the zone around the pipe, and use the cleaner fill there. Heavier material can go in above it once the line is protected.

Low garden spots

Garden spots that dip after a season of watering benefit from a shallow fill blended into the existing soil at the edges. Blend gradually so the transition does not create a new hollow, and water the area lightly to see where it pools before you plant.

Pricing Notes for Pasco Orders

Each order is sold by the ton. The live delivered price is shown for whichever ZIP code you enter, so the number you see includes delivery to that address.

Larger quantities bring the rate per ton down, so the price worth comparing is the one at the quantity your job really needs, not the smallest option.

Other Pasco materials use their own units. Premium Screened Topsoil is sold by the ton, while Mulch is sold by the cubic yard.

Ordering Fill Dirt in Pasco, WA

An order for a Pasco address comes down to three steps.

1. Convert your cubic yard estimate to tons, using the ratio above.
2. Enter the ZIP code for the drop address and read the delivered price the page returns.
3. Set the quantity and add it to the cart. Two tons is the least you can order, so a small repair may still need a full two-ton load.

Other Washington cities are listed on the Fill Dirt in Washington page.

About Fill Dirt

Fill dirt is a bulk subsoil used to build up low areas and give structure under finished surfaces. It is generally brown, dense, and easy to shape when it is slightly damp.

It contains little organic matter, so it is a poor choice for growing plants on its own. Most homeowners cover it with a richer layer of topsoil or a compost blend before they seed or plant.

Expect a mix of fine material and some larger pieces, since fill is not screened the way landscaping topsoil is. Remove stones or roots that would get in the way of a finish layer, and keep the material away from planting areas until you have looked it over.

What Fill Dirt costs in Pasco

In the Pasco market, fill dirt is sold by the ton and priced at the gate before delivery is added on. Send your ZIP and load size and we will send back a same-hour quote with the truck rate and the per-ton figure spelled out. One ton covers about 98 sq ft at a 3 inch finished depth, so a 400 sq ft driveway pad runs roughly 5 tons.

How crews use Fill Dirt in Pasco

Crews working out of Pasco tend to call for fill dirt on a few repeat jobs each week. The first is erosion control, typically laid in tight urban lots and infill builds with a base lift compacted before the finish course goes on. The second is driveway gravel, which lands here in dense neighborhoods where curb access is short and usually ships as a 4 to 8 ton order. With a population around 81,724, Pasco pulls a mix of single-truck homeowner orders and contractor full-loads through the season.

Delivery day in Pasco

On the day of the drop, the dispatcher pulls the closest yard, batches your ticket with other Pasco stops, and sends a window the night before. Tandem-axle dumps need at least 12 ft of clear width and 14 ft overhead to set the bed; tri-axles need 14 ft of clearance on both counts and a level pad to tip safely. Standard lead time on this lane is Mon-Sat, with same-day windows held open for orders that hit the desk before 11 AM and clear payment.

Estimate how much you need