Fill Dirt Delivery in Billings, MT for Yards and Pads

Fill dirt delivery in Billings, MT usually starts with a low spot in the yard, a patio edge that has sunk, or a driveway apron that needs more height. Billings has about 120,000 residents, so jobs range from small yard repairs to larger pads and regrading. Fill dirt is the bulk material you place under the finish layer to raise and level ground.

Common jobs for fill dirt delivery in Billings, MT

Most orders fall into a few categories:

• Raising a low corner of a backyard or side yard.
• Building up a pad under a shed, patio or walkway.
• Filling a hole left behind by an old stump, pool or septic work.
• Leveling ground before sod, pavers or gravel go down.

Some jobs combine two of these, such as leveling a side yard and building a pad at the same time, and one order can cover both. Fill dirt belongs below the finish. If the surface is a driveway or path, Asphalt Millings is worth comparing for a firm top layer. Where a layer has to be more open and loose, #57 Crushed Stone is the usual pick, with fill dirt set underneath it.

Choosing the drop spot and access

Pick a drop spot close enough to the work area that the material does not need to be carried far, but clear of the septic field, buried lines and any spot where a heavy load could crush something. Look at overhead wires and low branches along the route. Check that the gate is wide enough for a loaded truck to pass and that the ground at the drop spot can carry the weight without rutting. Move toys, planters and parked vehicles before the truck arrives.

How much fill dirt to order

For Billings fill dirt, start by measuring the area's length and width in feet and its depth in inches. Multiply length by width by depth, then divide by 324 to get cubic yards, and round up. This material is sold by the ton and weighs about 2,200 pounds per cubic yard, so one ton covers roughly 0.9 cubic yards. If the area is irregular, split it into rectangles, measure each one, and add the results together. Add a modest margin on top, because fill dirt drops as it is walked on and watered in over the first season. For a quick estimate, the calculator can work through the numbers with you.

Timing and ground conditions

Spread and compact fill when the ground is dry enough to walk on without leaving deep prints. Mud and frozen clumps do not compact well and leave soft spots later. Plan the work for a dry stretch, and avoid starting right after a heavy rain or while the ground is still frozen from a cold snap. Spread the material in layers of a few inches and tamp each one before adding the next.

Slope and drainage around the job

Finished fill should slope away from the foundation and any structures, so water runs off instead of pooling against the wall. The goal is a steady fall across the first few feet from the house. Once the surface is in place, check the grade with a long straight board and a level, and fix any low spots before you top the area with sod or pavers.

Pricing notes for Billings orders

The delivered price for your ZIP is calculated live and shown on the page before you order, so you do not need to work out freight by hand. Larger orders get a lower rate per ton, which means a bigger load often costs less per ton than a small one. Compare the total for the tonnage you actually need instead of looking only at the per-ton rate.

Ordering fill dirt in Billings

The smallest order is 2 tons. Have your quantity, your ZIP and a rough sketch of the drop area ready before you start, so the total matches the job. Enter your ZIP to see the delivered price, then choose your quantity in tons. For fill dirt in other Montana cities, start at Fill Dirt in MT. For the city-specific details, read about delivery in Billings before you place the order.

About Fill Dirt

About this material

Fill dirt is a brown bulk material in the Soil and Dirt category. It is used to raise grade, level low areas and build the layer that sits under pavers, sod or gravel. Each order is sold by the ton, so the quantity you pick is the weight that gets delivered to your address.

Density is the number that matters most when you plan a project. At about 2,200 pounds per cubic yard, this material weighs more per yard than mulch or compost, so compare bulk products by the ton rather than by the yard. Doing that keeps quantities honest across materials, and it makes the delivered price easy to read against the weight you need.

What Fill Dirt costs in Billings

Local Billings yards quote fill dirt by the ton; the delivered number includes fuel, the truck, and the haul. Send your ZIP and load size and we will send back a same-hour quote with the truck rate and the per-ton figure spelled out. A ton of this material spreads across about 98 sq ft when laid 3 inches deep, useful when you are sizing a patio base or a walkway run.

How crews use Fill Dirt in Billings

In and around Billings, fill dirt shows up most often on two project types. The most common deployment is erosion control, often in tight urban lots and infill builds in two to three inch lifts. Second on the list is driveway gravel, which we see in dense neighborhoods where curb access is short on partial-truck deliveries. At roughly 121,483 people, the Billings order mix leans toward 3 to 8 ton residential drops with the occasional 16 ton job for a contractor.

Delivery day in Billings

A typical Billings drop is dispatched from the closest yard with a two hour window and a heads-up call once the truck is loaded. Tandem trucks want a 12 ft lane in and out; tri-axles need 14 ft, and both want firm ground at the tipping spot so the load releases cleanly. Standard lead time on this lane is Mon-Sat, with same-day windows held open for orders that hit the desk before 11 AM and clear payment.

Estimate how much you need