Fill Dirt Delivery in Midland, TX by the Ton
Fill Dirt · Midland, TX

Fill Dirt Delivery in Midland, TX by the Ton

Bulk fill dirt delivered in Midland, TX. Brown color.

Starting from $443.15 delivered to Midland for 2 tons, our minimum order

Weight per yard 2200 lb Density 81.5 lb/cu ft

Fill dirt delivery in Midland, TX suits owners who need to raise a low spot, backfill a trench, or build up a yard before sod or a garden goes in. The material is sold by the ton and delivered to your address, so you order the amount the job needs instead of buying dozens of bags at a store.

Best Uses for Fill Dirt in Midland

Fill dirt is the layer under the finish, not the finish itself. If you plan to grow grass or flowers, top the filled area with Premium Screened Topsoil so roots have something to grow into.

Local Overview: Fill Dirt Delivery in Midland, TX

Midland sits on the flat Permian Basin plains, where wind, strong sun and dry summers shape how lots get graded and planted. The city has about 131,000 residents, and many of the yards here started out as raw or uneven ground, which means owners often need to rebuild the grade before anything else goes in.

Dry clay and caliche soils are common across the region. A yard that looks level after a wet spring can sink or crack once the ground dries out, and fill dirt gives you a clean base to rebuild that grade.

Many Midland owners also level the backyard before they add a shed, a raised bed or a play area. On a flat lot, every low spot shows once the grass is gone, so a small amount of fill in the right place makes the finished surface look intentional rather than patched.

Other Texas cities are listed on the Fill Dirt in Texas page, though the ground under a Midland lot shapes the details more than the material does.

Delivery to Midland Addresses

Orders go to your address in Midland. The delivery in Midland page covers the city service in more detail. Before you place an order, decide where the truck can stop and whether there is a clear path from the curb to the spot that needs fill. A narrow gate, a steep driveway or a fence line can turn a quick drop into a long walk with a shovel.

How Much Fill Dirt Your Midland Project Needs

Multiply length by width in feet, then by the depth in inches, and divide by 324 to get cubic yards. Take a 20 by 25 foot backyard pad filled 4 inches deep: that works out to about 6.2 cubic yards, and at 2,200 pounds per cubic yard it comes to close to 7 tons. Fill compresses as it is spread and watered in, so order a little more than the exact figure to avoid a short finish.

For a quicker answer, run your dimensions through the calculator.

Pricing Fill Dirt Delivered to Midland

Fill dirt is sold by the ton. Enter your ZIP and the page shows the delivered total for that address before you pay. Midland fill dirt orders get a lower rate per ton as they grow, and the smallest order is 2 tons.

Pair Fill Dirt With Other Materials in Midland

Some projects need more than one material. A path or drainage swale often gets Pea Gravel on top of the fill, which keeps the surface loose and easy to walk on. Choose the top layer for how the area will be used, then order the base material from this page.

Ordering Fill Dirt for Your Midland Job

  1. Round your estimate up to a whole number of tons.
  2. Type in the ZIP for the job address and read the total.
  3. Pay at checkout and save the confirmation.

Line up a rake, a wheelbarrow and a helper before you order, so spreading can start as soon as the fill is on the ground.

About Fill Dirt

Fill dirt is a brown, earthen material used to build up ground that sits too low, to fill voids, and to bring an area up to a finished grade. It is heavy once it is in place, weighing about 2,200 pounds per cubic yard, so it does the bulk of the lifting on a project while a finish layer handles the surface.

Homeowners use it under lawns, beside driveways and along new fence lines, and small contractors use it for backfill and site leveling. It is a poor choice for a surface that has to stay loose, because it is meant to be worked into place rather than left on top. Plan the finish material separately, whether that is topsoil for planting or a gravel for paths.

What Fill Dirt costs in Midland

In the Midland market, fill dirt is sold by the ton and priced at the gate before delivery is added on. Send your ZIP and load size and we will send back a same-hour quote with the truck rate and the per-ton figure spelled out. One ton covers about 98 sq ft at a 3 inch finished depth, so a 400 sq ft driveway pad runs roughly 5 tons.

How crews use Fill Dirt in Midland

Crews working out of Midland tend to call for fill dirt on a few repeat jobs each week. The first is erosion control, typically laid in tight urban lots and infill builds with a base lift compacted before the finish course goes on. The second is driveway gravel, which lands here in dense neighborhoods where curb access is short and usually ships as a 4 to 8 ton order. With a population around 131,325, Midland pulls a mix of single-truck homeowner orders and contractor full-loads through the season.

Delivery day in Midland

On the day of the drop, the dispatcher pulls the closest yard, batches your ticket with other Midland stops, and sends a window the night before. Tandem-axle dumps need at least 12 ft of clear width and 14 ft overhead to set the bed; tri-axles need 14 ft of clearance on both counts and a level pad to tip safely. Standard lead time on this lane is Mon-Sat, with same-day windows held open for orders that hit the desk before 11 AM and clear payment.

SAME CATEGORY

Related materials we deliver in Midland

Estimate how much you need

Work out your material

Cubic yards0 cu yds
Approximate weight0 tons

A planning figure, not a guarantee. Order roughly a tenth extra to cover settling and uneven ground.

PRODUCT & CITY HUBS

Browse more

PROJECTS

Common uses for Fill Dirt in Midland

NEARBY

Available in nearby cities

TOOLS

Plan your project

KEEP READING

Related guides

Frequently Asked Questions

Does caliche under my yard change how I use fill?

Caliche is hard and blocks drainage, so water can sit on top of it even under new fill. For a shallow leveling job that is usually acceptable. If you plan deep plantings or a drainage line, break through the layer with a bar or a rented breaker first, and keep the fill thickness in mind so low spots do not trap water.

How do I keep wind from stripping a freshly graded surface?

Bare fill dries quickly on the plains and can blow away as dust. Wet it lightly as you spread, then cover the surface soon with sod, seed or a layer of mulch. A shallow ridge of fill along the windward edge also helps hold the surface in place until the cover takes root.

How much slope does a flat lot need once it is filled?

Even a flat lot should shed water, so aim for a gentle fall away from buildings. Set a stake at the high point and another at the low end, run a string line between them, and check the drop with a line level. Add or rake fill until the fall is steady, with no flat patches in between.

How should I backfill an irrigation trench?

Return the soil in thin layers and wet each one lightly as you go, so the trench does not sink later. Keep rocks and clumps away from the pipe itself. Leave the top a little proud of the surrounding ground, since the fill will drop as it settles, then finish with sod or seed.

What can I do with fill left over after the job?

Spread it thinly across other low spots, or shape it into a low berm along a fence. Do not pile it against a wall or a tree trunk, because soil held against either can cause rot and moisture problems. A small leftover pile on a tarp stays usable for patching dips that show up later.

Should I keep fill away from the foundation wall?

Yes, keep the finished surface below the siding line and slope it away from the wall. Fill piled against the foundation can hold water against it and give pests an easy path in. Leave the area closest to the wall a little lower, then let the grade rise gradually as it moves away.

Can one load cover two separate spots on my lot?

Yes. Measure each area on its own, work out the tons for each, and add the numbers together before you order. Split the load by eye when it arrives, filling the lower or more important area first. Keep the ton count in mind when you spread so the second spot is not left short.

How do I blend new fill into the existing lawn edge?

Feather the fill so it thins out toward the lawn instead of ending in a sharp step. Cut a shallow edge in the old grass, lay the fill up to it, and rake the transition smooth. A gradual taper keeps the mower from scalping the edge and stops soil from washing out onto the lawn.

Order Fill Dirt →
0
    0
    Your Cart
    Your cart is emptyReturn to Shop