Fill Dirt Delivery in Kent, WA by the Ton

Fill dirt delivery in Kent, WA is bulk work. The material is sold by the ton and dropped at your address, which is a different job from buying bags at a garden center. Kent homeowners and small contractors usually order it to level a low yard, raise a garden bed, or bring grade up under a new patio or shed pad. This page covers the local picture, the jobs fill dirt suits, how to estimate tonnage, and how ordering works.

About Kent, Washington

Kent is a city of about 140,000 people in King County, south of Seattle in the Green River valley. Renton is about 5 miles away, Federal Way about 7 miles, Bellevue and Seattle about 16 miles each, and Redmond about 21 miles. A low corner or a sunken patch is one of the most common reasons people order fill, and it shows up on properties of every age, from older bungalows to newer builds.

Where Fill Dirt Works Best

• Leveling a low spot. A dip in the lawn that holds puddles after rain is a good candidate. Fill brings the surface back up to grade.
• Raising a garden bed. Build the bed up with fill, then finish the top few inches with a planting mix.
• Grade under a patio, walkway or shed pad. Bring the base to the height you need before the hardscape goes in.
• Rebuilding a driveway shoulder. Fill can restore the soil along an edge that has washed or sunk. For the driveway surface itself, #57 Crushed Stone is a common base.

Next to a house, set the finished grade so water runs away from the foundation. A flat or dished fill pools water against the wall, so shape the surface with a slight fall. If the job is a lot or a drive surface rather than a fill job, Asphalt Millings is worth comparing before you order.

Fill Dirt Delivery in Kent, WA

The truck needs a clear route from the street to the drop spot. Look for overhead branches, low wires, and gates or fences that must open wide enough for a loaded truck. Pick a spot as close to the work area as the driveway allows, and choose ground that will carry weight. Soft lawn or wet clay can rut under a heavy load, so a plywood or gravel path can protect it. Dry weather helps too. Wet fill is heavy and clings to a shovel, so spreading goes faster on a dry stretch of days. The delivery in Kent page covers the address side of the order.

How Much Fill Dirt You Need in Kent

Measure the area in feet and the depth you want to add in inches. Take the length and width at a few points, because yards rarely have straight edges, and average the depth across the spot instead of using the deepest corner. Kent projects start with length times width times depth, then dividing by 324 gives the cubic yard figure. If the math feels tedious, the calculator runs it from the same three numbers.

In Kent, fill dirt is sold by the ton. A cubic yard of it weighs about 2,200 pounds, and a ton is 2,000 pounds, so one ton covers roughly 0.9 cubic yard of loose material. Fill compacts once it is wet and walked on, so add a margin above the bare figure. Around ten percent extra is a reasonable starting point for most Kent yards, and a deeper fill calls for a larger margin.

Pricing Notes

The smallest order is 2 tons. Kent fill dirt orders show the delivered price for each ZIP, calculated live on the page, so the full figure appears before you commit. Larger orders get a lower rate per ton, which means a single larger load usually comes out cheaper per ton than a small top-up order placed later.

Ordering Fill Dirt in Kent

1. Choose fill dirt and set the quantity in tons, starting at 2.
2. Enter the delivery address and review the order summary.
3. Confirm the order once the drop spot is picked out and the route is clear.

For the statewide picture, see Fill Dirt in Washington. If the same yard also needs a different material, the Kent pages for Pea Gravel and River Rock cover those options.

About Fill Dirt

About this material

Fill dirt is a brown, bulk soil that builds up ground. It goes in when a spot needs more height, a flatter surface, or a firmer base, and it is rarely the finish layer people see once a project is done. Most of the material is mineral soil, so it is heavy for its volume and it packs down as it dries and gets walked on.

On a Kent job, fill dirt usually sits under something else: grass, a garden bed, a paver walk, or a slab base. That is why buyers care more about how much arrives than how the pile looks. The price is set per ton, so the weight of the load is the number that counts, and the material is picked for its structure rather than its appearance.

What Fill Dirt costs in Kent

In the Kent market, fill dirt is sold by the ton and priced at the gate before delivery is added on. Send your ZIP and load size and we will send back a same-hour quote with the truck rate and the per-ton figure spelled out. One ton covers about 98 sq ft at a 3 inch finished depth, so a 400 sq ft driveway pad runs roughly 5 tons.

How crews use Fill Dirt in Kent

Crews working out of Kent tend to call for fill dirt on a few repeat jobs each week. The first is erosion control, typically laid in tight urban lots and infill builds with a base lift compacted before the finish course goes on. The second is driveway gravel, which lands here in dense neighborhoods where curb access is short and usually ships as a 4 to 8 ton order. With a population around 136,588, Kent pulls a mix of single-truck homeowner orders and contractor full-loads through the season.

Delivery day in Kent

On the day of the drop, the dispatcher pulls the closest yard, batches your ticket with other Kent stops, and sends a window the night before. Tandem-axle dumps need at least 12 ft of clear width and 14 ft overhead to set the bed; tri-axles need 14 ft of clearance on both counts and a level pad to tip safely. Standard lead time on this lane is Mon-Sat, with same-day windows held open for orders that hit the desk before 11 AM and clear payment.

Estimate how much you need